Differences

This shows you the differences between two versions of the page.

--- 4.0.0:wireless_coinslot_flashing [2020/02/24 17:26]
admin [Flashing Guide For Wireless Coinslot]
+++ 4.0.0:wireless_coinslot_flashing [2024/02/04 01:20] (current)
@@ Line 1: / Line 1: @@
 ====== Flashing Guide For Wireless Coinslot ======
-For e-loading keypad setup, you need to add **Arduino** because ESP8266 boards have limited PINS. Just connect the Arduino's **TX** to ESP8266's **RX**. If they are on different power adapter source, link the module's ground. Please refer to  **[[Arduino for keypad]]** for more information. If you are looking for the configuration guide, refer to **[[4.0.0-beta.1:esp8266_configuration_guide|ESP8266 Configuration Guide]]**.
+For e-loading keypad setup, you need to add **Arduino** because ESP8266 boards have limited PINS. Just connect the Arduino's **TX** to ESP8266's **RX**. If they are on different power adapter source, link the module's ground. Please refer to  **[[4.0.0-beta.1:arduino_for_keypad]]** for more information. If you are looking for the configuration guide, refer to **[[4.0.0:esp8266_configuration_guide|ESP8266 Configuration Guide]]**.
 ===== Flash ESP8266 =====
@@ Line 8: / Line 8: @@
 ways to flash:
-  - [[4.0.0-beta.1:wireless_coinslot_flashing#using_pc | Using PC]]
+  - [[4.0.0:wireless_coinslot_flashing#using_pc| Using PC]]
-  - [[4.0.0-beta.1:wireless_coinslot_flashing#using_android_phone | Using Android Phone With OTG]]
+  - [[4.0.0:wireless_coinslot_flashing#using_android_phone| Using Android Phone With OTG]]
@@ Line 15: / Line 15: @@
 Softwares to Download:
   - Install [[ https://github.com/marcelstoer/nodemcu-pyflasher/releases | PyFlasher ]]
-  - Download [[ esp8266-firmware | ESP8266 Firmware ]]. Unzip the content of the zip file (esp8266-firmware-xxxxx.zip).
+  - Download [[ http://wiki.adopisoft.com/doku.php?id=4.0.0:software_image |ESP8266 Firmware ]].
@@ Line 24: / Line 24: @@
 Open **PyFlasher**.
-{{ :4.0.0-beta.1:pyflasher-1.png?direct&600 |}}
 Set proper **COM PORT**.
 Browse the ESP8266 firmware you downloaded (__esp8266-firmware-xxxxx.bin__).
-Set the **Baud Rate** to __921600__.
+Set the **Baud Rate** to __115200__.
-Leave the other settings to their default values.
-Click **Flash NodeMCU**
+{{ :4.0.0-beta.1:pyflasher-1.png?direct&600 |}}
-{{ :4.0.0-beta.1:pyflasher-2.png?direct&600 |}}
 ----
@@ Line 44: / Line 40: @@
 Softwares to Download:
   - Install [[ https://play.google.com/store/apps/details?id=com.bluino.esploader | ESP8266 Loader ]]
-  - Download [[ esp8266-firmware | ESP8266 Firmware ]]. Unzip the content of the zip file (esp8266-firmware-xxxxx.zip).
+  - Download [[ http://wiki.adopisoft.com/doku.php?id=4.0.0:software_image |ESP8266 Firmware ]].
 After downloading the needed softwares, connect the **ESP8266 Board** to your Android phone via **OTG**. Make sure you enable the OTG setting on your android.

AdoPiSoft Wiki

User Tools

Site Tools

Differences

Page Tools