Differences

This shows you the differences between two versions of the page.

--- 4.0.0:wireless_coinslot_flashing [2020/02/24 16:52]
admin
+++ 4.0.0:wireless_coinslot_flashing [2024/02/04 01:20] (current)
@@ Line 1: / Line 1: @@
 ====== Flashing Guide For Wireless Coinslot ======
-For e-loading keypad setup, you need to add **Arduino** because ESP8266 boards have limited PINS. Just connect the Arduino's **TX** to ESP8266's **RX**. If they are on different power adapter source, link the module's ground. Please refer to  **[[Arduino for keypad]]** for more information.
+For e-loading keypad setup, you need to add **Arduino** because ESP8266 boards have limited PINS. Just connect the Arduino's **TX** to ESP8266's **RX**. If they are on different power adapter source, link the module's ground. Please refer to  **[[4.0.0-beta.1:arduino_for_keypad]]** for more information. If you are looking for the configuration guide, refer to **[[4.0.0:esp8266_configuration_guide|ESP8266 Configuration Guide]]**.
 ===== Flash ESP8266 =====
@@ Line 8: / Line 8: @@
 ways to flash:
-  - [[4.0.0-beta.1:wireless_coinslot_flashing#using_pc | Using PC]]
+  - [[4.0.0:wireless_coinslot_flashing#using_pc| Using PC]]
-  - [[4.0.0-beta.1:wireless_coinslot_flashing#using_android_phone | Using Android Phone With OTG]]
+  - [[4.0.0:wireless_coinslot_flashing#using_android_phone| Using Android Phone With OTG]]
 === Using PC ===
+Softwares to Download:
+  - Install [[ https://github.com/marcelstoer/nodemcu-pyflasher/releases | PyFlasher ]]
+  - Download [[ http://wiki.adopisoft.com/doku.php?id=4.0.0:software_image |ESP8266 Firmware ]].
+After downloading the needed softwares, connect the ESP8266 Board to your PC and determine the **COM Port**.
+{{ :4.0.0-beta.1:pc-flash-arduino-1.png?direct&600 |}}
+Open **PyFlasher**.
+Set proper **COM PORT**.
+Browse the ESP8266 firmware you downloaded (__esp8266-firmware-xxxxx.bin__).
+Set the **Baud Rate** to __115200__.
+{{ :4.0.0-beta.1:pyflasher-1.png?direct&600 |}}
+----
@@ Line 18: / Line 40: @@
 Softwares to Download:
   - Install [[ https://play.google.com/store/apps/details?id=com.bluino.esploader | ESP8266 Loader ]]
-  - Download [[ esp8266-firmware | ESP8266 Firmware ]]. Unzip the content of the zip file (esp8266-firmware-xxxxx.zip).
+  - Download [[ http://wiki.adopisoft.com/doku.php?id=4.0.0:software_image |ESP8266 Firmware ]].
 After downloading the needed softwares, connect the **ESP8266 Board** to your Android phone via **OTG**. Make sure you enable the OTG setting on your android.
@@ Line 27: / Line 49: @@
 {{ :4.0.0-beta.1:esp8266-loader-s1.png?direct&600 |}}
-Tap the green upload icon at the right to start uploading.
+Tap the **green upload icon** at the right to start uploading.
 {{ :4.0.0-beta.1:esp8266-loader-s2.jpg?direct&600 |}}

AdoPiSoft Wiki

User Tools

Site Tools

Differences

Page Tools